Skip to product information

BMW Alpine White III 300 Touch Up Spray Paint

BMW Alpine White III 300 Touch Up Spray Paint

Counts toward up to 20% off when you spend $300+

Black FridayEnds Mon, Nov 30

Up To 20% Off When You Spend $300+

  • 10%$300+
  • 15%$600+
  • 20%$1,000+
  • + Suit$1,500+

This item counts toward it. Applied automatically at checkout.

OEM Color Details
Make: BMW
Color code: 300
Color name: ALPINWEISS III
Year: 1993–2027
Select Color Quantity How Many Cans Do I Need?
BMW Alpine White III 300 Touch Up Spray Paint | OEMatch
$39.99
Spraycan
-
1
+
Color
2
Groundcoats
3
2k Top Coat
4
+
Finish the Job
step image

Description

Fix damage on a vehicle that came in BMW 300 Alpine White III, or add this factory color to smaller parts on any other vehicle.

What BMW 300 Alpine White III Looks Like

This is BMW 300 Alpine White III, a white with a solid finish. It is a flat, even color with no flake. We mix it to the factory formula. Matching your factory paint? Check that the paint code on your vehicle's label reads 300.

What You Need to Spray It

Alpine White III is a 2-stage color. Like all our OEMatch basecoats, it goes over our Gray AP-7541g Sealer as the ground coat and must be topped with Alpha Automotive Clearcoat for gloss and protection. It doesn't need an undercoat. New to this? Read our paint kit instructions and tips.

Spraying Tips for Solid Colors

Solid colors are the easiest to blend: build even coats until the color fully hides the surface.

Choosing This Spray Can

Use the spray can for touch ups and small areas. Each can is filled to order with this color, ready to spray. Painting a panel? Get the BMW 300 basecoat paint. Painting the whole vehicle? The BMW 300 complete car paint kit has everything packed together.

Application & Prep

STEP 1 – CLEAN THE SURFACE

1 - Wash with soap and water, rinse, and dry completely.

2 - Degrease using wax and grease remover or isopropyl alcohol.

3 - Wipe dry with a clean, lint-free towel.

STEP 2 – SCUFF / SAND FOR ADHESION

If Raw Plastic / Polyurethane: Evenly scuff bare plastic or raw surfaces. These will also need to be adhesion promoted prior to paint using our WolfBite Adhesion promoter.

If Good Condition OEM Paint: Sand smooth or glossy paint with P320-P400 grit sand paper or Scuff Pad until uniformly dull with no glossy areas.

If Surface Needs Bodywork or heavy scratches removed: Sand the damaged areas with 180 grit (feathered out into the panel) then do your bodywork. Finish in 220 Grit sanding. Then spot prime with high build primer - fading the primer out into the rest of the sanded panel covering the bodywork and any 220 grit scratches. (the good condition areas of the panel should have been sanded in 320-400 or scuff pad). Lastly, after the high build primer is dry and ready to be sanded (check tds for timeline), sand with 320-400 to match the rest of the panel.

After The above prep: Remove dust with compressed air or a clean microfiber towel.

STEP 3 – FINAL WIPE & TACK

1 - Wipe the surface again with isopropyl alcohol or wax and grease remover.

2 - Allow solvents to fully evaporate.

3 - Lightly wipe with a tack cloth immediately before spraying. Do not press hard. (optional but great step)

STEP 4 – SET UP YOUR SPRAY AREA

1 - Use a well-ventilated, well-lit area with good extraction fans

2 - Ideal conditions are 65–75°F (18–24°C) with 40–60% relative humidity.

3 - Keep the area free of open flames, sparks, or ignition sources.

4 - Wet the floor if your space allows to keep dust down

5 - Cover any items or areas in your space that you do not want to get overspray on

STEP 5 – PERSONAL PROTECTION

1 - Wear a respirator rated for organic or solvent vapors.

2 - Use nitrile gloves and safety goggles.

3 - Wear a paint suit

STEP 6 – SHAKE THE CAN

1 - Shake vigorously for 45–60 seconds.

2 - Invert the can several times while shaking to fully mix pigments and metallics.

STEP 7 – TEST SPRAY

ALWAYS DO A TEST SPRAY + SPRAY OUT CARD IF DOING OEM SPOT JOBS

1 - Spray on cardboard or a scrap panel.

2 - Confirm even spray pattern, correct color, and proper atomization.

3 - Adjust the spray can's nozzle to match your spray style or surface.

4 - If the can is not operating correctly, remove the cap completely, reseat it on the can, and twise the entire nozzle 360 degrees. Since our cans are made to order, sometimes there is slight paint build up and reseating the nozzle corrects this.

STEP 8 – SPRAYING TECHNIQUE

1 - Hold the can 5–6 inches from the surface.

2 - Keep the can perpendicular, 90 degrees to the panel at all times.

3 - Move at a steady speed using smooth, even passes. You are looking for medium wet coats NOT super wet, pooling coats.

4 - Overlap each pass by 50 percent.

STEP 9 – TRIGGER CONTROL

1 - Begin moving before pulling the trigger. Start off of the panel then move onto the panel. This avoids build up on edges.

2 - Fully depress the trigger while spraying.

3 - Release the trigger completely at the end of each pass.

4 - Stop spraying after clearing the panel edge by an inch.

STEP 10 – COATS & FLASH TIMES

1k Primer/Sealer

1 - Spray a medium wet coat on the entire panel (if not blending oem paint) to achieve a 75% coverage. This fills in the sanding scratches as well as gives a uniform , required ground coat color for the next steps.

2- Allow to flash dry for 5-15 minutes. Time depends on the product and environment.

3 - Apply the second medium-wet coat to achieve full coverage

4 - Allow to dry for 30 minutes or until the wet look fades so a dull, even finish and is completely dry to the touch.

GROUNDCOATS or SOLID COLORS (BEFORE MIDCOATS IF APPLICABLE)

This is for our Base Black, OEM Undercoats or solid colored basecoats. Not all projects require this step.

1 - Apply the first medium-wet coat at approximately 75 percent coverage.

2 - Allow to flash 5-15 minutes or until the wet look fades so a dull, even finish. Time depends on the product and environment.

3 - Apply the second medium-wet coat to achieve full coverage

4 - Allow to flash 5-15 minutes or until the wet look fades so a dull, even finish. Time depends on the product and environment.

5 - Apply a Third medium wet coat if the color is not 100% covered and even at this point. This will vary based on the color and product being sprayed.

4 - Flash another 15-30 minutes. Until the surface is even, dull, an dry to the touch.

MIDCOAT , CUSTOM COLORS , OR METALLIC/ PEARL OEM

This is for coverage over required groundcoats , not "ghost effect"

1 - Apply medium coats over the required groundcoat for your color.

2 - Flash 5–15 minutes between coats or until tack-free.

3 - Apply additional coats until the desired color depth is achieved. Most custom and oem colors require 2-4 medium coats - check color description or compare to existing oem panels

4 - Apply 1 light "control" coat to make sure all of the pearl or metallic is even and not splotchy or "tiger striped"

5 - Once the entire surface, even cracks and crevices, is completely dry to the touch, wait 15 minutes in a temperature-controlled paint booth. In any other environment at 70°F or warmer, wait 30 minutes to 1 hour. Then move on to the topcoat step.

EFFECT PEARL / COLORSHIFT COAT

This is for effect over light groundcoats (not for coverage)

1 - Apply one light effect coat at approximately 25 percent coverage.

2 - Allow 5-15mins for the coat to flash before adding another light coat (if you want to add more effect)

Repeat as many times to your preference of effect and coverage.

3 - Once the entire surface, even cracks and crevices, is completely dry to the touch, wait 15 minutes in a temperature-controlled paint booth. In any other environment at 70°F or warmer, wait 30 minutes to 1 hour. Then move on to the topcoat step.

STEP 11 – CLEANUP & STORAGE

CAP CLEARING

1 - Turn the can upside down after spraying.

2 - Spray until only clear propellant comes out.

3 - This clears paint from the valve and prevents clogging.

NOZZLE CARE

1 - Remove the spray nozzle after use.

2 - Wipe clean with solvent.

3 - Do not soak the nozzle in solvent.

STORAGE

1 - Store cans upright in a cool, dry place.

2 - Keep away from direct sunlight.

3 - Avoid freezing conditions.

4 - Do not store above 120°F (49°C).

QUICK TROUBLESHOOTING

1 - Dry or rough texture means the can is too far away or moving too fast.

2 - Runs or sags mean the can is too close or moving too slowly.

3 - Continue to shake and agitate the can between coats- Repeat step 6

4 - If ever unsure the color is 100% covered (and you are going for coverage) - one extra coat is always a good idea.

Frequent Questions
Will this match my BMW's 300 paint?
Yes. It's mixed to the factory formula for BMW 300 Alpine White III. Check that the paint code on your vehicle reads 300.
What years and models use 300?
BMW used 300 on the 7 Series (1993–2027), 5 Series (1993–2027) and 3 Series (1993–2027), among others.
Do I need an undercoat for Alpine White III?
No. Alpine White III is a 2-stage color: basecoat, then clearcoat.
Where do I find my paint code?
On the paint code label, usually in the driver door jamb or under the hood.
Can I use this color on a vehicle that didn't come with it?
Yes. Many people use factory colors to customize other vehicles. You'll use the same sealer and clearcoat.
View full details

OEMatch Factory Color

BMW Alpine White III 300

Mixed to the factory formula for BMW paint code 300, used 1993–2027. Mixed to order, usually ships in 1–3 business days.

Will This Fit My Car?

300 Alpine White III came on 68 vehicles. Pick yours to check.

MakeModelYears
BMW 1 Series E87/E81 2004-2011 2004–2011
BMW 1 Series F20/F21 2011-2019 2011–2019
BMW 1 Series F40 2019- 2019–2027
BMW 2 Series Active Tourer U06 2022- 2022–2026
BMW 2 Series Active/Gran Tourer F45/F46 2014-2021 2014–2021
BMW 2 Series Coupe G42 2021- 2021–2026
BMW 2 Series Coupe/Cabrio F22 2014-2021 2014–2021
BMW 3 Series E36 1990-1998 1993–1998

Color Details

Make
BMW
Paint code
300
Color name
Alpine White III
Years
1993–2027
Stage
2-Stage
Finish
Solid
Color family
White
Ground coat
Gray sealer
Paint type
Solvent-based urethane basecoat

Find Your Paint Code

Every vehicle has a paint code label. Match it before you order: our paint is mixed to order, so it can't be returned.

  • Driver's door jambThe most common spot, on the sticker with the tire pressures.
  • Under the hoodOn the radiator support or the strut tower.
  • Trunk or spare tire wellCommon on older and European vehicles.

Look for the word Paint or Color next to the code. Yours should read 300.

Questions About This Color

Will this match my BMW's 300 paint?

Yes. It's mixed to the factory formula for BMW 300 Alpine White III. Check that the paint code on your vehicle reads 300.

What years and models use 300?

BMW used 300 on the 7 Series (1993–2027), 5 Series (1993–2027) and 3 Series (1993–2027), among others.

Do I need an undercoat for Alpine White III?

No. Alpine White III is a 2-stage color: basecoat, then clearcoat.

Where do I find my paint code?

On the paint code label, usually in the driver door jamb or under the hood.

Can I use this color on a vehicle that didn't come with it?

Yes. Many people use factory colors to customize other vehicles. You'll use the same sealer and clearcoat.

What Makes Our Spray Cans Different!

Recently viewed