Skip to product information

Audi Offroad Gray Metallic M3 Touch Up Spray Paint

Audi Offroad Gray Metallic M3 Touch Up Spray Paint

Audi · Paint Code M3

2-StagePearlXirallicMetallic1983–2025

Will this fit my car?Check the 18 vehicles that came in this color Check

Counts toward up to 20% off when you spend $300+

Black FridayEnds Mon, Nov 30

Up To 20% Off When You Spend $300+

  • 10%$300+
  • 15%$600+
  • 20%$1,000+
  • + Suit$1,500+

This item counts toward it. Applied automatically at checkout.

OEM Color Details
Make: AUDI
Color code: M3
Color name: OFFROAD GREY M.
Year: 1983–2025
Select Color Quantity How Many Cans Do I Need?
Audi Offroad Gray Metallic M3 Touch Up Spray Paint | OEMatch
$55.99
Spraycan
-
1
+
Color
2
Groundcoats
3
2k Top Coat
4
+
Finish the Job
step image

Description

Fix damage on a vehicle that came in Audi M3 Offroad Gray Metallic, or add this factory color to smaller parts on any other vehicle.

What Audi M3 Offroad Gray Metallic Looks Like

Audi Offroad Gray Metallic (M3) is a dark gray with a cool undertone and a pearl xirallic metallic finish. Fine flake sparkles in direct light and the pearl shifts the shade with the viewing angle. Check that your vehicle's paint code label reads M3.

What You Need to Spray It

Offroad Gray Metallic is a 2-stage color. Like all our OEMatch basecoats, it goes over our Gray AP-7541g Sealer as the ground coat and must be topped with Alpha Automotive Clearcoat for gloss and protection. It doesn't need an undercoat. New to this? Read our paint kit instructions and tips.

Spraying Tips for Pearl Xirallic Metallic

Hold the can the same distance and overlap every pass so the flake lies evenly, and blend into the next panel.

Choosing This Spray Can

Use the spray can for touch ups and small areas. Each can is filled to order with this color, ready to spray. Painting a panel? Get the Audi M3 basecoat paint. Painting the whole vehicle? The Audi M3 complete car paint kit has everything packed together.

Other Names for This Paint

It's the same factory formula as Karmann's Offroad Gray Metallic (M3) and Volkswagen's Offroad Gray Metallic (M3).

Application & Prep

STEP 1 – CLEAN THE SURFACE

1 - Wash with soap and water, rinse, and dry completely.

2 - Degrease using wax and grease remover or isopropyl alcohol.

3 - Wipe dry with a clean, lint-free towel.

STEP 2 – SCUFF / SAND FOR ADHESION

If Raw Plastic / Polyurethane: Evenly scuff bare plastic or raw surfaces. These will also need to be adhesion promoted prior to paint using our WolfBite Adhesion promoter.

If Good Condition OEM Paint: Sand smooth or glossy paint with P320-P400 grit sand paper or Scuff Pad until uniformly dull with no glossy areas.

If Surface Needs Bodywork or heavy scratches removed: Sand the damaged areas with 180 grit (feathered out into the panel) then do your bodywork. Finish in 220 Grit sanding. Then spot prime with high build primer - fading the primer out into the rest of the sanded panel covering the bodywork and any 220 grit scratches. (the good condition areas of the panel should have been sanded in 320-400 or scuff pad). Lastly, after the high build primer is dry and ready to be sanded (check tds for timeline), sand with 320-400 to match the rest of the panel.

After The above prep: Remove dust with compressed air or a clean microfiber towel.

STEP 3 – FINAL WIPE & TACK

1 - Wipe the surface again with isopropyl alcohol or wax and grease remover.

2 - Allow solvents to fully evaporate.

3 - Lightly wipe with a tack cloth immediately before spraying. Do not press hard. (optional but great step)

STEP 4 – SET UP YOUR SPRAY AREA

1 - Use a well-ventilated, well-lit area with good extraction fans

2 - Ideal conditions are 65–75°F (18–24°C) with 40–60% relative humidity.

3 - Keep the area free of open flames, sparks, or ignition sources.

4 - Wet the floor if your space allows to keep dust down

5 - Cover any items or areas in your space that you do not want to get overspray on

STEP 5 – PERSONAL PROTECTION

1 - Wear a respirator rated for organic or solvent vapors.

2 - Use nitrile gloves and safety goggles.

3 - Wear a paint suit

STEP 6 – SHAKE THE CAN

1 - Shake vigorously for 45–60 seconds.

2 - Invert the can several times while shaking to fully mix pigments and metallics.

STEP 7 – TEST SPRAY

ALWAYS DO A TEST SPRAY + SPRAY OUT CARD IF DOING OEM SPOT JOBS

1 - Spray on cardboard or a scrap panel.

2 - Confirm even spray pattern, correct color, and proper atomization.

3 - Adjust the spray can's nozzle to match your spray style or surface.

4 - If the can is not operating correctly, remove the cap completely, reseat it on the can, and twise the entire nozzle 360 degrees. Since our cans are made to order, sometimes there is slight paint build up and reseating the nozzle corrects this.

STEP 8 – SPRAYING TECHNIQUE

1 - Hold the can 5–6 inches from the surface.

2 - Keep the can perpendicular, 90 degrees to the panel at all times.

3 - Move at a steady speed using smooth, even passes. You are looking for medium wet coats NOT super wet, pooling coats.

4 - Overlap each pass by 50 percent.

STEP 9 – TRIGGER CONTROL

1 - Begin moving before pulling the trigger. Start off of the panel then move onto the panel. This avoids build up on edges.

2 - Fully depress the trigger while spraying.

3 - Release the trigger completely at the end of each pass.

4 - Stop spraying after clearing the panel edge by an inch.

STEP 10 – COATS & FLASH TIMES

1k Primer/Sealer

1 - Spray a medium wet coat on the entire panel (if not blending oem paint) to achieve a 75% coverage. This fills in the sanding scratches as well as gives a uniform , required ground coat color for the next steps.

2- Allow to flash dry for 5-15 minutes. Time depends on the product and environment.

3 - Apply the second medium-wet coat to achieve full coverage

4 - Allow to dry for 30 minutes or until the wet look fades so a dull, even finish and is completely dry to the touch.

GROUNDCOATS or SOLID COLORS (BEFORE MIDCOATS IF APPLICABLE)

This is for our Base Black, OEM Undercoats or solid colored basecoats. Not all projects require this step.

1 - Apply the first medium-wet coat at approximately 75 percent coverage.

2 - Allow to flash 5-15 minutes or until the wet look fades so a dull, even finish. Time depends on the product and environment.

3 - Apply the second medium-wet coat to achieve full coverage

4 - Allow to flash 5-15 minutes or until the wet look fades so a dull, even finish. Time depends on the product and environment.

5 - Apply a Third medium wet coat if the color is not 100% covered and even at this point. This will vary based on the color and product being sprayed.

4 - Flash another 15-30 minutes. Until the surface is even, dull, an dry to the touch.

MIDCOAT , CUSTOM COLORS , OR METALLIC/ PEARL OEM

This is for coverage over required groundcoats , not "ghost effect"

1 - Apply medium coats over the required groundcoat for your color.

2 - Flash 5–15 minutes between coats or until tack-free.

3 - Apply additional coats until the desired color depth is achieved. Most custom and oem colors require 2-4 medium coats - check color description or compare to existing oem panels

4 - Apply 1 light "control" coat to make sure all of the pearl or metallic is even and not splotchy or "tiger striped"

5 - Once the entire surface, even cracks and crevices, is completely dry to the touch, wait 15 minutes in a temperature-controlled paint booth. In any other environment at 70°F or warmer, wait 30 minutes to 1 hour. Then move on to the topcoat step.

EFFECT PEARL / COLORSHIFT COAT

This is for effect over light groundcoats (not for coverage)

1 - Apply one light effect coat at approximately 25 percent coverage.

2 - Allow 5-15mins for the coat to flash before adding another light coat (if you want to add more effect)

Repeat as many times to your preference of effect and coverage.

3 - Once the entire surface, even cracks and crevices, is completely dry to the touch, wait 15 minutes in a temperature-controlled paint booth. In any other environment at 70°F or warmer, wait 30 minutes to 1 hour. Then move on to the topcoat step.

STEP 11 – CLEANUP & STORAGE

CAP CLEARING

1 - Turn the can upside down after spraying.

2 - Spray until only clear propellant comes out.

3 - This clears paint from the valve and prevents clogging.

NOZZLE CARE

1 - Remove the spray nozzle after use.

2 - Wipe clean with solvent.

3 - Do not soak the nozzle in solvent.

STORAGE

1 - Store cans upright in a cool, dry place.

2 - Keep away from direct sunlight.

3 - Avoid freezing conditions.

4 - Do not store above 120°F (49°C).

QUICK TROUBLESHOOTING

1 - Dry or rough texture means the can is too far away or moving too fast.

2 - Runs or sags mean the can is too close or moving too slowly.

3 - Continue to shake and agitate the can between coats- Repeat step 6

4 - If ever unsure the color is 100% covered (and you are going for coverage) - one extra coat is always a good idea.

Frequent Questions
Will this match my Audi's M3 paint?
Yes. It's mixed to the factory formula for Audi M3 Offroad Gray Metallic. Check that the paint code on your vehicle reads M3.
What years and models use M3?
Audi used M3 from 1983–2025.
Do I need an undercoat for Offroad Gray Metallic?
No. Offroad Gray Metallic is a 2-stage color: basecoat, then clearcoat.
Where do I find my paint code?
On the paint code label, usually in the driver door jamb or under the hood.
Can I use this color on a vehicle that didn't come with it?
Yes. Many people use factory colors to customize other vehicles. You'll use the same sealer and clearcoat.
Is Audi M3 the same paint as Karmann M3?
Yes. It's the same factory formula as Karmann's Offroad Gray Metallic (M3).
View full details

OEMatch Factory Color

Audi Offroad Gray Metallic M3

Mixed to the factory formula for Audi paint code M3, used 1983–2025. Mixed to order, usually ships in 1–3 business days.

Will This Fit My Car?

M3 Offroad Gray Metallic came on 18 vehicles. Pick yours to check.

MakeModelYears
Volkswagen Amarok Gen1 2010-2022 2010–2022
Volkswagen Amarok Gen2 2022- 2022
Volkswagen Caddy Mk1 1979-1995 1983–1995
Volkswagen Caddy Mk2 1995-2003 1995–2003
Volkswagen Caddy Mk3 2003-2015 2003–2015
Volkswagen Caddy Mk4 2015-2020 2015–2020
Volkswagen Caddy Mk5 2020- 2020–2025
Volkswagen Fox 2003-2021 2014

Color Details

Make
Audi
Paint code
M3
Color name
Offroad Gray Metallic
Years
1983–2025
Stage
2-Stage
Finish
Pearl, Xirallic, Metallic
Color family
Gray
Ground coat
Gray sealer
Paint type
Solvent-based urethane basecoat
Also listed as
Karmann Offroad Gray Metallic (M3), Volkswagen Offroad Gray Metallic (M3), Offroad Grey Metallic

Find Your Paint Code

Every vehicle has a paint code label. Match it before you order: our paint is mixed to order, so it can't be returned.

  • Driver's door jambThe most common spot, on the sticker with the tire pressures.
  • Under the hoodOn the radiator support or the strut tower.
  • Trunk or spare tire wellCommon on older and European vehicles.

Look for the word Paint or Color next to the code. Yours should read M3.

Questions About This Color

Will this match my Audi's M3 paint?

Yes. It's mixed to the factory formula for Audi M3 Offroad Gray Metallic. Check that the paint code on your vehicle reads M3.

What years and models use M3?

Audi used M3 from 1983–2025.

Do I need an undercoat for Offroad Gray Metallic?

No. Offroad Gray Metallic is a 2-stage color: basecoat, then clearcoat.

Where do I find my paint code?

On the paint code label, usually in the driver door jamb or under the hood.

Can I use this color on a vehicle that didn't come with it?

Yes. Many people use factory colors to customize other vehicles. You'll use the same sealer and clearcoat.

Is Audi M3 the same paint as Karmann M3?

Yes. It's the same factory formula as Karmann's Offroad Gray Metallic (M3).

What Makes Our Spray Cans Different!

Recently viewed